打浆过程预添加CMC对杨木APMP浆悬浮液屈服应力的影响

doi:10.3969/j.issn.0253-2417.2017.02.014

林产化学与工业 ›› 2017, Vol. 37 ›› Issue (2): 108-114.doi: 10.3969/j.issn.0253-2417.2017.02.014

打浆过程预添加CMC对杨木APMP浆悬浮液屈服应力的影响

陈树润^1,2, 沙九龙^1,2, 何晶^1,2, 王晨^1,2, 沈军³, 张辉^1,2

1. 南京林业大学江苏省制浆造纸科学与技术重点实验室, 江苏南京 210037;
2. 南京林业大学江苏省林业资源高效加工利用协同创新中心, 江苏南京 210037;
3. 江苏理文造纸有限公司, 江苏常熟 215536

收稿日期:2016-08-26 出版日期:2017-04-25 发布日期:2017-05-04
通讯作者: 张辉,教授,博士生导师,研究领域为制浆造纸节能减排技术与装备、造纸机械状态监测与故障诊断技术;E-mail:hgzh@njfu.edu.cn。 E-mail:hgzh@njfu.edu.cn
作者简介:陈树润(1990-),男,山东烟台人,硕士生,研究方向：制浆造纸节能减排技术与装备
基金资助:
江苏省制浆造纸科学与技术重点实验室开放基金（201609）；江苏高校优势学科建设工程资助项目（无编号）

Influence of Addition of CMC Before Refining on the Yield Stress of Refined Poplar APMP Pulp Fiber Suspension

CHEN Shurun^1,2, SHA Jiulong^1,2, HE Jing^1,2, WANG Chen^1,2, SHEN Jun³, ZHANG Hui^1,2

1. Jiangsu Provincial Key Lab of Pulp and Paper Science and Technology, Nanjing Forestry University, Nanjing 210037, China;
2. Jiangsu Co-innovation Center for Efficient Processing and Utilization of Forest Resources, Nanjing Forestry University, Nanjing 210037, China;
3. Jiangsu Lee & Man Paper Co., Ltd., Changshu 215536, China

Received:2016-08-26 Online:2017-04-25 Published:2017-05-04

摘要/Abstract

摘要： 为考察打浆过程中添加羧甲基纤维素钠（CMC-Na）对杨木碱性过氧化氢化学机械浆（APMP浆）悬浮液屈服应力的影响，在分析杨木APMP浆打浆度与屈服应力关系的基础上，先添加一定量的CMC-Na对杨木APMP浆进行预处理10 min后，再分别用瓦利打浆机和PFI磨打浆处理，分析不同打浆方式以及添加CMC-Na预处理后对杨木APMP浆的打浆度和屈服应力的影响。结果表明：对于相同打浆度的杨木APMP浆，屈服应力（τ_y）随着浆料质量分数（C_m）的增加而迅速增加，且符合指数方程τ_y=aC_m^b，其中a与b值与打浆方式和打浆度的大小密切相关；经低浓度游离状的瓦利打浆机处理的浆料，其屈服应力随着打浆度的增加而减小，而中高浓度黏状的PFI磨打浆处理结果则相反。打浆过程预添加CMC-Na时，浆料打浆度随CMC-Na添加量（以绝干浆质量计）的增加先升高后降低；当CMC-Na添加量为2%并预处理 10 min 时，经瓦利打浆机处理的浆料打浆度可由45°SR提高到48°SR，而经PFI磨处理的浆料打浆度可由40°SR提高到50°SR，并且浆料悬浮液的屈服应力均达到最低值，分别为16.4和22.8 Pa（浆料质量分数为3%）。

关键词: 杨木, APMP, 打浆, CMC-Na, 屈服应力

Abstract: In order to study the influence of the addition of CMC-Na before refining on the yield stress of refined poplar APMP pulp fiber suspension, a certain amounts of CMC-Na were added to the APMP and the APMP were pretreated for 10 min before individually refining by Valley beater and PFI mill. The influences of the refining and CMC-Na pretreatment on the beating degree and yield stress (τ_y) of poplar APMP fiber suspension were analyzed respectively. It was found that the yield stress of the poplar APMP fiber suspensionwith a similar beating degree increased rapidly with the rising of CMC-Na concentration, and the yield stress was accordance with the concentration (C_m)via a power relationship of τ_y=aC_m^b(the values of a and b were closely related with the beating ways and beating degree). After refining under a low concentration by free beating device(e.g. Valley beater), the yield stress of the poplar APMP fibers suspension decreased with the increased beating degree, while reverse results were observed under the medium concentration refining by shiny beating device (e.g. PFI mill). After 2% CMC-Na (based on the dry pulp weight) was added the pulp and pretreated for 10 min, the beating degree of poplar APMP was increased to 48°SR from 45°SR with valley beater refining and ascended to 50°SR from 40°SR with PFI refining. Meanwhile, the yield stresses of the poplar APMP fibers suspension were reached to the minimum value with the same beating conditions, the minimum values of the yield stresses were 16.4 Pa and 22.8 Pa (PFS mass fraction was 3%), respectively.

Key words: poplar, APMP, refining, CMC-Na, yield stress

中图分类号:

TQ35
TS734

陈树润, 沙九龙, 何晶, 王晨, 沈军, 张辉. 打浆过程预添加CMC对杨木APMP浆悬浮液屈服应力的影响[J]. 林产化学与工业, 2017, 37(2): 108-114.

CHEN Shurun, SHA Jiulong, HE Jing, WANG Chen, SHEN Jun, ZHANG Hui. Influence of Addition of CMC Before Refining on the Yield Stress of Refined Poplar APMP Pulp Fiber Suspension[J]. Chemistry and Industry of Forest Products, 2017, 37(2): 108-114.

参考文献

[1] BOUSFIELD D W. Rheological Issues in the Paper Industry[M]//Rheology Reviews. S.l.:The British Society of Rheology, 2008:47-70.
[2] KEREKES R J. Pulp flocculation in decaying turbulence:A literature review[J]. Journal of Pulp and Paper Science, 1983, 9(3):86-91.
[3] BENNINGTON C P J, KEREKES R J, GRACE J R. The yield stress of fibre suspensions[J]. The Canadian Journal of Chemical Engineering, 1990, 68(10):748-757.
[4] GULLICHSEN J, HARKONEN E. Medium consistency technology.1. Fundamental data[J]. Tappi Journal, 1981, 64(6):69-72.
[5] KEREKES R J, SOSZYNSKI R M, DOO P A T. The Flocculation of Pulp Fibres[M]//Fundamental Rearch Symposium. PUNTON V(ed.).Papermaking Raw Materials. London:Mechanical Engineering Publications Ltd., 1985:265-310.
[6] SWERIN A, POWELL R L, ODBERG L. Linear and nonlinear dynamic viscoelas-ticity of pulp fibre suspensions[J]. Nordic Pulp & Paper Research Journal, 1992, 7(3):126-143.
[7] DAMANI R, POWELL R L, HAGEN N. Viscoelastic characterization of medium consistency pulp suspensions[J]. The Canadian Journal of Chemical Engineering, 1993, 71(5):676-685.
[8] RASTEIRO M G, BALNCO C A V, NEGRE C, et al. Modeling pulp fiber suspension rheology[J]. Tappi Journal, 2007, 6(7):17-23.
[9] DERAKHSHANDEH B, HATZIKIRIAKOS S G, BENNINGTON C P J, et al. Rheology of pulp suspensions using ultrasonic Doppler velocimetry[J]. Rheologica Acta, 2010,49(11):1127-1140.
[10] BENNINGTON C P J, AZEVEDO G, JOHN D A, et al. The yield stress of medium and high consistency mechanical pulp fibre suspensions at high gas contents[J]. Journal of Pulp and Paper Science, 1995, 21(4):111-118.
[11] PETTERSSON J, RASMUSON A. The yield stress of gas/liquid/fibre suspensions[J]. The Canadian Journal of Chemical Engineering, 2004, 82(6):1313-1318.
[12] CHEN K F, CHEN S M. The determination of the critical shear stress for fluidization of medium consistency suspensions of straw pulps[J]. Nordic Pulp & Paper Research Journal, 1991, 6(1):20-22.
[13] SHA J L, NIKBAKHT A, WANG C, et al. The effect of consistency and freeness on the yield stress of chemical pulp fibre suspensions[J]. Bioresources, 2015,10(3), 4287-4299.
[14] SHA J L, MITRA S, NIKBAKHT A, et al.The effect of blending ratio and crowding number on the yield stress of mixed hardwood and softwood pulp fiber suspensions[J]. Nordic Pulp & Paper Research Journal, 2015,30(4):634-639.
[15] SHA J L, ZHANG F, ZHANG H. Thixotropic flow behavior in chemical pulp fiber suspensions[J]. Bioresources, 2016,11(2):3481-3493.
[16] 陈淑梅,陈克复.纤维悬浮液在流送中的启动阻力[J].华南理工大学学报:自然科学版, 1995, 23(10):34-38. CHEN S M, CHEN K F. Start flowing resistance of the fibre suspension[J].Journal of South China University of Technology:Natural Science, 1995,23(10):34-38.
[17] 沙九龙. 浆纤维悬浮液的屈服应力与触变特性的研究[D]. 南京:南京林业大学博士学位论文,2016. SHA J L. The yield and thixotropic flow behavior in pulp fiber suspension[D].Nanjing:Doctoral Dissertation of Nanjing Forestry University, 2016.
[18] 张权,韩卿.化学助剂及预处理方法在打浆过程中的应用[J].中国造纸,2009,28(5):64-67. ZHANG Q, HAN Q. Development of technologies with chemical additives and pretreament[J].China Pulp and Paper,2009,28(5):64-67.
[19] 黄钊,何北海,赵广磊,等.CMC辅助打浆对竹浆纤维特性及成纸性能的影响[J].中国造纸,2007,26(2):1-4. HUANG Z, HE B H, ZHAO G L,et al. Effects of CMC addition during beating pulp of bamboo on its fiber and paper properties[J].China Pulp and Paper,2007,26(2):1-4.
[20] 文琼菊,邱先琴,毛建伟,等.打浆过程中添加助剂CMC的初步研究[J].黑龙江造纸,2013(3):1-2. WEN Q J, QIU X Q,MAO J W,et al. Preliminary study on additives of CMC refining process[J]. Heilongjiang Pulp and Paper,2013(3):1-2.

打浆过程预添加CMC对杨木APMP浆悬浮液屈服应力的影响

Influence of Addition of CMC Before Refining on the Yield Stress of Refined Poplar APMP Pulp Fiber Suspension

PDF (PC)

可视化

摘要/Abstract

引用本文

使用本文

参考文献

相关文章 15

编辑推荐

Metrics

本文评价

关于本刊

投稿指南

在线期刊

相关单位

联系我们

[1]	王鹏飞, 任浩, 翟华敏. 杨木碳水化合物自水解特征的P因子调控[J]. 林产化学与工业, 2019, 39(4): 65-71.
[2]	马红亮, 陈健, 焦健, 邓拥军, 孔振武, 房桂干. 长链硅烷改性杨木纤维的制备及其表征[J]. 林产化学与工业, 2019, 39(3): 25-33.
[3]	马红亮, 陈健, 焦健, 邓拥军, 孔振武, 房桂干. 有机硅氧烷改性杨木纤维的制备及其表征[J]. 林产化学与工业, 2018, 38(6): 20-26.
[4]	冯年捷, 汪继明, 谢益民, 杨鑫, 刘达岸. 杨木预水解液中木质素质量浓度的P因子调控作用[J]. 林产化学与工业, 2018, 38(4): 35-40.
[5]	王鹏, 秦影, 傅英娟, 王兆江, 张凤山. 杨木自水解液中溶解木质素和胶体木质素的结构特征[J]. 林产化学与工业, 2017, 37(4): 59-66.
[6]	王晨, 郑学梅, 张辉, 沙九龙, 程金兰. 纤维尺寸对漂白硫酸盐木浆悬浮液屈服应力的影响[J]. 林产化学与工业, 2017, 37(3): 89-94.
[7]	程富江, 刘廷志, 李祥祥, 亓晖, 钟丽鸣. 桉木APMP制浆废水抽出物提取及其抑藻效应研究[J]. 林产化学与工业, 2017, 37(2): 57-64.
[8]	邵思成, 吴初柱, 陈克利. 稻草氧碱浆打浆特性的研究[J]. 林产化学与工业, 2017, 37(2): 148-154.
[9]	李凤凤, 陈嘉川, 张志礼, 杨桂花, 庞志强. 杨木粉在EmimAC离子液体中溶解性能的研究[J]. 林产化学与工业, 2015, 35(5): 22-28.
[10]	申莉红, 杨桂花, 陈嘉川. 纤维素酶预处理对杨木APMP浆配抄性能的影响[J]. 林产化学与工业, 2014, 34(6): 105-110.
[11]	董长青;张智博;廖航涛;陆强. 基于Py-GC-MS的杨木和松木快速热解比较研究[J]. 林产化学与工业, 2013, 33(6): 41-47.
[12]	陈健;孔振武;焦健;房桂干;吴国民;霍淑平. 异氰酸酯/硅烷偶联剂接枝改性杨木粉的制备及其表征[J]. 林产化学与工业, 2013, 33(1): 1-7.
[13]	黄志义;冯永顺;于志明;母军. 杨木刨花板的热解动力学分析[J]. 林产化学与工业, 2012, 32(5): 83-87.
[14]	曾健;陈克复;谢剑平;许光;李军;饶国华;杨飞;高文花. 打浆对烟梗纤维成纸性能的影响[J]. 林产化学与工业, 2012, 32(5): 101-105.
[15]	陈健;孔振武;焦健;房桂干;吴国民;霍淑平;聂明才. 桐马酸酐甲酯改性杨木纤维增强环氧树脂复合材料性能研究[J]. 林产化学与工业, 2011, 31(6): 25-28.